Charles 3641-80 Podręcznik Użytkownika

Section 360−381−C02Equipment Issue 2Third Printing, August 2006Telecommunications Group2006 Charles Industries Ltd.All rights reserved. Printed in Un

Section 360−381−C0210Figure 9. Performance Monitor screen with 15-Minute Performance Data4.5.1. 15-Minute PM DataUse the following steps to look at 1

Section 360−381−C02114.5.3. Reset PM DataUse to clear stored data. Select Now to reset data at the current time, or select Today to reset data from th

Section 360−381−C0212Use the following steps to enable/disable the tone test.Step Action System Response1. Select which card you want to test (Card 1,

Section 360−381−C0213Use the following steps to enable/disable the test.Step Action System Response1. Select the channel number(s) on any card youwant

Section 360−381−C02144.10 Loopback Test (Nx64 − Primary T1 Only)Use the Loopback test to check where on the line problems are occurring when an alarm

Section 360−381−C02154.11 Loopback Test (ISDN − Primary T1 Only)Use the Loopback test to check where on the line problems are occurring when an alarm

Section 360−381−C02164.12 Loopback Test (DSU/OCU − Primary T1 Only)Use the Loopback test to check where on the line problems are occurring when an ala

Section 360−381−C02174.13 System Alarm StatusUse this selection to retrieve current alarms in the system. Highlight System Alarm Status and press <

Section 360−381−C0218Figure 14. Setting the Time Slot Allocation4.15.1. Time Slot MappingUse the following steps to change the time slot mapping. Ste

Section 360−381−C0219Step System ResponseAction9. Repeat steps 4 and 5 to map any other channelsthat are not allocatedChannels are mapped.10. Press &l

Section 360−381−C0221. GENERAL1.1 Document PurposeThis document describes how to use the Charles 360-80 Intelligent Channel Bank (ICB) Craft Terminal

Section 360−381−C02204. Use the arrow keys to highlight the desired direc-tion and press <Enter>Asks you which mode you want to set—Bdct=broadca

Section 360−381−C0221Parameter DescriptionOptionTTLP Level (dBm) −10.0 to +6.0 dBm Transmit TLP levelRTLP Level (dBm) −10.0 to +6.0 dBm Receive TLP le

Section 360−381−C0222Parameter DescriptionOptionOperating Mode FXS/GS Ground startFXS/LS Loop startPLARD/D3 Private line automatic ringdownPLARD/D4 Pr

Section 360−381−C0223Parameter Option DescriptionChannel Selection 1−12 (if in Card 1 slot) Select the channel the parameters will be appliedto Each

Section 360−381−C0224Parameter DescriptionOptionZero Code Suppression Enable/Disable Select to transmit a code if an all-zero byte is detectedSpeed Su

Section 360−381−C0225Parameter DescriptionOptionDSR Control Yes Force data set readyNo NormalDCD Control Yes Force data carrier detectNo NormalInterfa

Section 360−381−C0226Parameter Option DescriptionChannel Selection 1−4 (if in Card 1 slot) Select the channel the parameters will be appliedto Each c

Section 360−381−C0227Parameter DescriptionOptionChannel Type RS530 Select the serial interface connection typeV.35V.36 (RS−449/422)RS232HIZ (factory t

Section 360−381−C0228Parameter Option DescriptionNx56/64K 1 thru 24 Depends on bandwidth desired and time slots allocatedBase Setting 56K or 64K Base

Section 360−381−C0229Step Action System Response1. Select Delete Existing User and press <Enter> Ask for the user’s name2. Type in the user’s na

Section 360−381−C023Step Action System Response1. If using a PC, open your terminal emulator soft-ware.If using an ASCII terminal, press <Enter>

Section 360−381−C02308. SNMP CONFIGURATION8.1 SNMP Community TableFor SNMP management, the T1-S is addressed using a combination of the following: IP

Section 360−381−C02318.2 Trap IP TableTraps must be enabled in this table and through the MIB (instance iadTrapSetProxy under iadTrapMgt) to be gen-er

Section 360−381−C0232Far−End loopback traps will be generated at the far−end equipment.9. ADDRESSING/SUBNET MASK/GATEWAY//MAC ADDRESS MENUFor the NMS/

Section 360−381−C0233Applying changes to this table will initiate a warm start and momentarily disrupt T1 service.WARNINGThe MAC address is unique for

Section 360−381−C0243. MAIN MENU3.1 Equipment StatusOnce logged-in to the craft interface, communication is established with the T1-S allowing the sta

Section 360−381−C025Menu Selection Use to...IP Address/SubnetMask/MAC GatewayAddress MessageSet IP address, subnet mask and gateway addressLogout Log

Section 360−381−C026Menu Selection Use To...System Alarm Status Retrieve system alarms (display only)ICB Card RTC Time Set the system real-time clockT

Section 360−381−C027Parameter DescriptionOptionCGAProcess ModeNormal Carrier group alarm response characteristics per 43801Process ModeCM2 Carrier gro

Section 360−381−C0284.2.1. Retrieve and Set Secondary T1 ParametersThe Secondary T1 Parameter Menu, as shown in Figure 7, allows you to specify each o

Section 360−381−C0294.4 Loopback Test for T1Use the Loopback test to troubleshoot T1 line problems. Be aware that service will be affected by these te